Details
This kit contains all you need to make a fully working Mendel v2 3D printer (build size 20x20x14cm).
This kit comes standard with additional items such as: kapton tapes, heated bed for ABS & PLA, power supply, usb cable, few mtr PLA etc to make sure its a complete kit.
This complete mendel parts kit contains:
* Generation 6 Electronics - incl opto's on correct cable lengths with molex connectors and high temp cable for connecting heater and thermistor,
* Kit 2 - all hardware cut - steel 8.8 (bearings, belts, bars,studding & bolts,nuts, washers)
* Kit 8 - all thick & thin sheet for Mendel incl GEN6 & heated bed (6mm POM electronics sheet, 4mm Alu frog and purge plate, 5mm pre-drilled printbed and 1mm Alu thin sheet (opto-flags))
* Reprapped Plastics - Mendel v2 plastic set & Extruder plastics for hotend v9
* Motor set of 4 - incl correct cable lengths and molex connectors (plug n play with GEN6)
* Semi-Profi printed belt pullies (grubscrew version).
* Semi-Profi printed Z-axis-opto spring + z-optobracket
* Semi-Profi printed Z-driven-pullies
* Semi-Profi printed Z-manual adjust knob
* M4 brass insert piece v2 - for direct drive on motorshaft (5mm inner hole)
* Hot end v9 partially pre-assembled, incl heaterblock, thermistor,heat resistor, Alu thick sheet (base& motorholder), cooling fan etc
* Silicone sealant upto 300C - 75ml (for placing thermistor/resistor in heater block)
* Kapton tape * high temp heatshrink - diameter 2.4mm- length 20cm (connecting heater and thermistor cables)
* Uninsulated bootlace ferrules - 10pc 1.0mm² & 10pc 0.5mm² (connecting heater and thermistor cables)
* 2x SET of 4 steel comp. springs 28.5Lx9mm dia (4 for extruder+ 4 for printbed)
* Set of 4 Heater blocks 4x 1.0 Ohm (for heated printbed)
* Cooling paste upto 150C - 3gr (to use in between printbed and heater blocks)
* PTFE 1mm sheet 25x70mm (8pc 12,5x12,5mm (use under the springs of printbed for insulation) and 2x 10x25mm to connect cables/use as strain-relief)
* Power Supply 70W 12-24V 110-240V (power GEN6 @ 12V)
* Power Supply 90W 12-22V for heated bed (ABS & PLA)
* USB A-B cable 3mtr
* Cable ties (100pc)
* Feet for Mendel
* few mtr of PLA for first tests
With our electronics/opto's/motors, you won't need to solder anything, no need to buy any extra cables or connectors. All that needs to be done, is connect the powersupply with 2 screws in the green connector. Rest of all the wiring is plug n play.
(except extruder nichrome+thermistor off course, but we have included high temp cables+bootlace ferrules+hightemp heatshrink for that.)
NOTE: Mendel printed plastics production time is now around 1-2 weeks, so once an order is placed it can take another 2 weeks before your plastics are printed and your order is ready to ship, in stock means here PRE-ORDER
High res pictures: click here
This kit comes standard with additional items such as: kapton tapes, heated bed for ABS & PLA, power supply, usb cable, few mtr PLA etc to make sure its a complete kit.
This complete mendel parts kit contains:
* Generation 6 Electronics - incl opto's on correct cable lengths with molex connectors and high temp cable for connecting heater and thermistor,
* Kit 2 - all hardware cut - steel 8.8 (bearings, belts, bars,studding & bolts,nuts, washers)
* Kit 8 - all thick & thin sheet for Mendel incl GEN6 & heated bed (6mm POM electronics sheet, 4mm Alu frog and purge plate, 5mm pre-drilled printbed and 1mm Alu thin sheet (opto-flags))
* Reprapped Plastics - Mendel v2 plastic set & Extruder plastics for hotend v9
* Motor set of 4 - incl correct cable lengths and molex connectors (plug n play with GEN6)
* Semi-Profi printed belt pullies (grubscrew version).
* Semi-Profi printed Z-axis-opto spring + z-optobracket
* Semi-Profi printed Z-driven-pullies
* Semi-Profi printed Z-manual adjust knob
* M4 brass insert piece v2 - for direct drive on motorshaft (5mm inner hole)
* Hot end v9 partially pre-assembled, incl heaterblock, thermistor,heat resistor, Alu thick sheet (base& motorholder), cooling fan etc
* Silicone sealant upto 300C - 75ml (for placing thermistor/resistor in heater block)
* Kapton tape * high temp heatshrink - diameter 2.4mm- length 20cm (connecting heater and thermistor cables)
* Uninsulated bootlace ferrules - 10pc 1.0mm² & 10pc 0.5mm² (connecting heater and thermistor cables)
* 2x SET of 4 steel comp. springs 28.5Lx9mm dia (4 for extruder+ 4 for printbed)
* Set of 4 Heater blocks 4x 1.0 Ohm (for heated printbed)
* Cooling paste upto 150C - 3gr (to use in between printbed and heater blocks)
* PTFE 1mm sheet 25x70mm (8pc 12,5x12,5mm (use under the springs of printbed for insulation) and 2x 10x25mm to connect cables/use as strain-relief)
* Power Supply 70W 12-24V 110-240V (power GEN6 @ 12V)
* Power Supply 90W 12-22V for heated bed (ABS & PLA)
* USB A-B cable 3mtr
* Cable ties (100pc)
* Feet for Mendel
* few mtr of PLA for first tests
With our electronics/opto's/motors, you won't need to solder anything, no need to buy any extra cables or connectors. All that needs to be done, is connect the powersupply with 2 screws in the green connector. Rest of all the wiring is plug n play.
(except extruder nichrome+thermistor off course, but we have included high temp cables+bootlace ferrules+hightemp heatshrink for that.)
NOTE: Mendel printed plastics production time is now around 1-2 weeks, so once an order is placed it can take another 2 weeks before your plastics are printed and your order is ready to ship, in stock means here PRE-ORDER
High res pictures: click here